flange area
英 [flændʒ ˈeəriə]
美 [flændʒ ˈeriə]
翼缘区
双语例句
- Send a fool to France, and a fool he will return again. Quality Control for Anchored Flange Used in Transportation of Gas from Sichuan to Eastern Area
傻瓜送到法兰西，回国仍旧带傻气。川气东送工程用锚固法兰的质量控制 - Apply primer to the window flange in the area of the marking.
将底漆喷涂在标记区域的车窗法兰上。 - It is found that the cause of the fracture is the stress concentration at the hinge axle flange area.
通过分析铰链的加工过程，认为裂纹产生的原因是由于铆接时铰链轴凸缘部位应力集中造成的。 - The flange area between the lid hinge and lid must be sealed with sprayable sealing strip during each reinstallation.
在每次重新安装时，必须用可喷式密封条将盖铰链和盖之间的法兰区域密封。 - The urethane liner is cast in place to form a continuous liner throughout the entire body, chest, packing chamber and flange face area.
氨基甲酸乙酯衬垫采用定点浇铸工艺，在整个阀体、阀腔、填料腔和法兰面区域表面形成全面连续的覆盖衬垫。 - Circle flange forming by prefabricated elliptical hole in stainless steel elbow Analytical Model for Cross-Sectional Area of Workpiece in Round-Oval-Round Pass Sequence in Bar Rolling
不锈钢弯管上用预制椭圆孔翻边成形圆孔棒材轧制圆-椭圆-圆孔型中轧件面积计算模型 - Quality Control for Anchored Flange Used in Transportation of Gas from Sichuan to Eastern Area
川气东送工程用锚固法兰的质量控制 - Valves can also be furnished with flange bolt holes drilled for through bolting, except in the chest area.
阀门也可以配置法兰螺栓孔，用于贯穿式螺栓，但不能穿过阀腔区域。 - The stress, strain and the mold force are analyzed by using the main stress method and the stress strain change rule along with the die angle of the inside hole flange forming area is obtained.
用主应力法对内孔翻边成形过程中变形区的应力、应变及模具上的受力进行了理论分析，得出了变形区的应力、应变随冲模斜角的变化规律。 - Lingual flange area extension of full denture: clinical analysis of 23 cases
全口义齿舌翼区伸展固位23例临床分析 - Shear Stress and Shear Deformation of the Flange Deformed Area in Box Drawing
盒形件拉深时法兰变形区的剪应力与剪切变形 - The actuality of the research of leakage models, gaskets performances, sealing materials and the design of the bolts flange connections is introduced and some opinions about the further development in this area are presented.
介绍了泄漏模型、垫片性能、密封材料及螺栓法兰连接系统设计方法的研究现状，对其进一步发展提出了一些看法。 - Temperature Sensors were introduced on the exterior face of the flange plate to measure the temperature of the radiated area so as to make necessary adjustments timely of current, volt, focus, etc.
为防止因此导致扫描盒前端法兰盘局部温升过高，在法兰的外侧安装温度传感器以实时监测受照点的温度，从而及时调整系统的电流、电压、聚焦等有关参数。 - With the stress and strain rate distribution in the flange must being continuous, it cause that a great many particles of circular angle area flow into straight side area in the deep-drawing process of panel part.
这一特征就是，在覆盖件的拉深过程中，由于板坯的凸缘面上的应力及应变速率的分布必须连续，从而导致圆角区域的大量质点流入了直边区域中。 - In of displacement induces shear stress. Shear deformation this paper, flow law of material is theoretically analysed based on deformation of the flange deformed area in box drawing.
针对盒形件拉深成形时法兰变形区的变形进行了材料塑性流动的理论分析，提出了位移速度差诱发剪应力的观点。 - The simulation results showed that the product overall had a good springback, but the springback was out of tolerance in the local flange area.
模拟结果表明产品整体回弹情况良好，但局部区域法兰边回弹超差。